- 您现在的位置：买卖IC网 > Sheet目录878 > RVB0G151MNG (Nichicon)CAP ALUM 150UF 4V 20% SMD
Precautions
2. Mounting precautions
(1) Things to know before mounting
a) Do not reuse the FPCAP that has already been assembled in a device and energized.
Excluding the FPCAP that has been removed for measuring electrical characteristics during a periodic inspection,
they cannot be reused.
b) Leakage current may increase if the part has been stored for a long period of time.
In this case, use after voltage treatment under the rated voltage.
(2) Mounting-1
a) Mount after checking the capacitance and the rated voltage.
b) Mount after checking the polarity.
c) Do not drop on the floor and do not use parts that have been dropped.
d) Do not deform and then mount.
(3) Mounting-2
a) Mount after checking the match between the lead pitch and the PC board holes pitch.
b) When an automatic insertion equipment is used to clinch the lead wires, make sure it is set correctly.
c) Be careful of the shock force that can be produced by the automatic insertion equipment.
d) Do not apply excessive external force to the lead wires, the FPCAP itself, or the electrode terminals.
(4) Soldering with a soldering iron
a) Set the soldering conditions (temperature, time) so that they fall within the range stipulated by the catalog specification.
b) When the lead wire terminal must be processed because the terminal spacing and the PC board holes spacing do not match,
process it before soldering so that no stress is applied to the FPCAP itself.
c) Do not subject the FPCAP itself to excessive stress when soldering with a soldering iron.
d) When a soldering iron is used to repair the FPCAP that has already been soldered once and needs to be removed,
do it after the solder has been completely melted so that no stress is applied to the FPCAP terminals.
e) Do not let the tip of the soldering iron touch the FPCAP itself.
f ) The amount of leakage current after soldering may increase a slightly (from a few μ A to several hundred μ A) depending
on the soldering condition (preheating and solder temperature and time, PC board material and thickness, etc.)
The leakage current can be reduced by applying voltage.
(5) Flow soldering (Radial lead type)
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μ A to several
hundred μ A) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP.
e) Flow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
(6) Reflow soldering (SMD type)
Do not use reflow soldering for Radial lead type (Through Hole).
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μ A to several
hundred μ A) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP .
e) Reflow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
f) Do not use VPS (Vapor Phase Soldering).
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
3
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
RW-4815D
CONV DC/DC 3W 36-72VIN +/-15VOUT
RW-483.3S/SMD
CONV DC/DC 3W 36-72VIN 3.3VOUT
RW2-483.3D/H3/SMD
CONV DC/DC 2W 36-72VIN +/-3.3V
RY-0505D
CONV DC/DC 1W DL +/-5V OUT SIP7
RZ-2415S-R
CONV DC/DC 0.5W 24VIN 15VOUT
S1008R-393K
INDUCTOR SHIELDED 39UH SMD
S100J25U2MU6BK0R
CAP CER 10PF 6KV 5% RADIAL
S102M43Z5P283L6R
CAP CER 1000PF 1.5KV 20% RADIAL
相关代理商/技术参数
RVB0G221MNG
功能描述:铝质电解电容器-SMD 4.0V 220uF TOL 20%
RoHS:否 制造商:Nichicon 电容:220 uF 容差:20 % 电压额定值:4 V ESR:15 mOhms 工作温度范围:- 55 C to + 105 C 尺寸:4.3 mm W x 7.3 mm L x 2.8 mm H 产品:Low ESR Electrolytic Capacitors
RVB0J101MNG
功能描述:铝有机聚合物电容器 100 UF 6.3V 20%
RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel
RVB0J151MNG
功能描述:铝质电解电容器-SMD 6.3V 150uF TOL 20%
RoHS:否 制造商:Nichicon 电容:150 uF 容差:20 % 电压额定值:6.3 V ESR:20 mOhms 工作温度范围:- 55 C to + 105 C 尺寸:4.3 mm W x 7.3 mm L x 2.8 mm H 产品:Low ESR Electrolytic Capacitors
RVB1C270MNG
功能描述:27μF 16V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:27μF 容差:±20% 额定电压:16V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1C330MNG
功能描述:33μF 16V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:33μF 容差:±20% 额定电压:16V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1C470MNG
功能描述:47μF 16V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:47μF 容差:±20% 额定电压:16V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1E150MNG
功能描述:15μF 25V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:15μF 容差:±20% 额定电压:25V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1
RVB1E270MNG
功能描述:27μF 25V Aluminum - Polymer Capacitors 2917 (7343 Metric) 30 mOhm 1000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，VB 包装:剪切带（CT） 零件状态:过期 电容:27μF 容差:±20% 额定电压:25V ESR（等效串联电阻）:30 毫欧 不同温度时的使用寿命:105°C 时为 1000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:1.4A 阻抗:- 引线间距:- 大小/尺寸:0.287" 长 x 0.169" 宽（7.30mm x 4.30mm） 高度 - 安装（最大值）:0.118"（3.00mm） 表面贴装焊盘尺寸:- 安装类型:表面贴装 封装/外壳:2917（7343 公制） 标准包装:1